Skip to main content

Ohm's Law

CI

CircuitSim

·

Created Oct 3, 2026

·

Updated Oct 3, 2026

Preview will appear once the owner saves the schematic
Details

Components

2


Schematic

Yes


Simulation

DC operating point


Copies

Not copied yet

About this circuit

Discover how voltage and resistance set current in a simple DC circuit. Predict the result, inspect voltage and current, and try two guided experiments.

Circuit notes

Ohm's Law

Voltage pushes current through resistance. In this circuit, V1 supplies 5 V5\,\mathrm{V} and R1 has a resistance of 1 kΩ1\,\mathrm{k}\Omega. Ohm's law predicts the current before you run the simulation:

I=VR=5 V1 kΩ=0.005 A=5 mA\begin{aligned} I &= \frac{V}{R} \\ &= \frac{5\,\mathrm{V}}{1\,\mathrm{k}\Omega} \\ &= 0.005\,\mathrm{A} = 5\,\mathrm{mA} \end{aligned}

This relationship helps you choose resistors and estimate current in DC circuits. A larger voltage produces more current; a larger resistance produces less current.

Read the circuit

Start at the positive terminal of V1, follow the upper wire through R1, and return along the bottom wire. Conventional current flows clockwise. The ground symbol marks the 0 V0\,\mathrm{V} reference; it is not a separate power source.

  • Vr1 measures the top of R1 relative to ground. Because its lower terminal is grounded, this is the voltage across the resistor.
  • Ir1 measures the current flowing toward R1. Its arrow defines the positive measurement direction.

The probes measure the circuit without materially changing it. A negative current reading would mean flow opposite to the probe's arrow.

Observe in CircuitSim

This example opens with DC Operating Point selected and runs automatically. Read Vr1=5 V\mathrm{Vr1} = 5\,\mathrm{V} and Ir1=5 mA\mathrm{Ir1} = 5\,\mathrm{mA} in the Table panel. These are steady values, so a time chart would add no information.

R1 converts electrical energy to heat. Its calculated power is:

P=VI=(5 V)(5 mA)=0.025 W=25 mW\begin{aligned} P &= VI \\ &= (5\,\mathrm{V})(5\,\mathrm{mA}) \\ &= 0.025\,\mathrm{W} = 25\,\mathrm{mW} \end{aligned}

Power is calculated here; it is not a third measured table row.

Try it

Select a component and edit its value in the Properties panel, then use Run simulation to update the results. Change only the field named below; leave advanced parameters at their defaults.

ExperimentChangePredict the current
Double the voltageV1: DCMag (DC voltage) from 5 V5\,\mathrm{V} to 10 V10\,\mathrm{V}; keep R1 at 1 kΩ1\,\mathrm{k}\Omega10 mA10\,\mathrm{mA}: twice the voltage gives twice the current
Double the resistanceRestore V1 to 5 V5\,\mathrm{V}; R1: Resistance from 1 kΩ1\,\mathrm{k}\Omega to 2 kΩ2\,\mathrm{k}\Omega2.5 mA2.5\,\mathrm{mA}: twice the resistance gives half the current

Before running, predict each result yourself. After experimenting, restore V1 to 5 V5\,\mathrm{V} and R1 to 1 kΩ1\,\mathrm{k}\Omega and rerun.

Model assumptions

The source holds its specified voltage and the resistor has constant resistance. Real sources have limits, and real resistors have tolerance, temperature dependence, and a power rating. This example isolates the basic voltage–current relationship.

Components used

Components used
2 components
NameManufacturerMPNCountType

DC Voltage Source

Generic

—

1

Official

Resistor

Generic

—

1

Official

Try this circuit yourself

Free to get started. No download — runs in your browser with a full SPICE engine.