Skip to main content

Resistors

CI

CircuitSim

·

Created Oct 3, 2026

·

Updated Oct 3, 2026

Preview will appear once the owner saves the schematic
Details

Components

2


Schematic

Yes


Simulation

DC operating point


Copies

Not copied yet

About this circuit

Compare current and power in two resistors across the same voltage. Change resistance and supply voltage to explore how each affects the results.

Circuit notes

Resistors

At the same voltage, a larger resistance lets less current flow. R1 is 1 kΩ1\,\mathrm{k}\Omega and R2 is 2 kΩ2\,\mathrm{k}\Omega. Each resistor connects between the same 6 V6\,\mathrm{V} supply and ground, so each has the full supply voltage across it.

I1=6 V1 kΩ=6 mAI2=6 V2 kΩ=3 mA\begin{aligned} I_1 &= \frac{6\,\mathrm{V}}{1\,\mathrm{k}\Omega} = 6\,\mathrm{mA} \\ I_2 &= \frac{6\,\mathrm{V}}{2\,\mathrm{k}\Omega} = 3\,\mathrm{mA} \end{aligned}

Doubling resistance halves current when voltage stays constant. The values 1 kΩ1\,\mathrm{k}\Omega and 2 kΩ2\,\mathrm{k}\Omega mean 1000 Ω1000\,\Omega and 2000 Ω2000\,\Omega; enter them as 1k and 2k in the Resistance field.

Read the circuit

V1 supplies the upper wire. Current divides into the two resistor branches, flows downward, and returns to V1 along the bottom wire. Junction dots show connected branches. The ground symbol defines the 0 V0\,\mathrm{V} reference.

  • Vs, in green, measures the upper wire relative to ground: the voltage across both resistors.
  • Ir1, in blue, measures current through R1.
  • Ir2, in purple, measures current through R2.

The current arrows point toward the resistors and define positive readings. The supply delivers the sum, 6+3=9 mA6 + 3 = 9\,\mathrm{mA}; this total is calculated, not a separate table row. The probes do not materially change the circuit.

Observe in CircuitSim

This example opens with DC Operating Point selected and runs automatically. The Table panel shows Vs = 6.0 V, Ir1 = 6.0 mA, and Ir2 = 3.0 mA. These steady values are best compared in a table.

Resistors convert electrical energy into heat. At a fixed voltage, P=VI=V2/RP = VI = V^2/R, so the larger resistor also dissipates less power here:

P1=(6 V)(6 mA)=36 mWP2=(6 V)(3 mA)=18 mW\begin{aligned} P_1 &= (6\,\mathrm{V})(6\,\mathrm{mA}) \\ &= 36\,\mathrm{mW} \\ P_2 &= (6\,\mathrm{V})(3\,\mathrm{mA}) \\ &= 18\,\mathrm{mW} \end{aligned}

Power is calculated here, not measured in the table. The comparison assumes equal voltage; at equal current, P=I2RP = I^2R instead increases with resistance.

Try it

Select a component, edit the named field in the Properties panel, then use Run simulation. Predict the readings before running; leave advanced parameters at their defaults.

  1. Make the resistors equal. Change R2's Resistance from 2k to 1k, keeping V1 at 6 V6\,\mathrm{V}. Both currents become 6 mA6\,\mathrm{mA} and each resistor dissipates 36 mW36\,\mathrm{mW}. R1's current stays the same because the ideal source maintains its voltage.
  2. Halve the voltage. Restore R2 to 2k, then change V1's DCMag from 6 to 3. Ir1 becomes 3 mA3\,\mathrm{mA} and Ir2 becomes 1.5 mA1.5\,\mathrm{mA}. Each current halves, while power falls to one quarter: 9 mW9\,\mathrm{mW} and 4.5 mW4.5\,\mathrm{mW}.

Restore V1 = 6, R1 = 1k, and R2 = 2k, then rerun.

Model assumptions

These ideal resistors have constant resistance and no polarity. Reversing a resistor's terminals does not change its behavior. Real resistors have tolerance, temperature dependence, and a power rating; this model does not simulate heating or failure. The ideal source holds its specified voltage as the load changes.

Components used

Components used
2 components
NameManufacturerMPNCountType

Resistor

Generic

—

2

Official

DC Voltage Source

Generic

—

1

Official

Try this circuit yourself

Free to get started. No download — runs in your browser with a full SPICE engine.