Skip to main content

Inductors in Parallel

CI

CircuitSim

·

Created Oct 3, 2026

·

Updated Oct 3, 2026

Preview will appear once the owner saves the schematic
Details

Components

3


Schematic

Yes


Simulation

Transient analysis


Copies

Not copied yet

About this circuit

Explore how inductors combine in parallel. Compare equivalent value, branch-current sharing, and the charging or current-rise time constant.

Circuit notes

Inductors in Parallel

Parallel inductors share the same voltage. Their combined inductance is smaller than either one. L1 is 1.5 H and L2 is 3 H; the pair is equivalent to 1 H for the zero-current start used here.

1Leq=1L1+1L2Leq=L1L2L1+L2=1 Hτ=Leq100 Ω=10 ms\begin{aligned} \frac{1}{L_{\mathrm{eq}}} &= \frac{1}{L_1}+\frac{1}{L_2} \\ L_{\mathrm{eq}} &= \frac{L_1L_2}{L_1+L_2} = 1\,\mathrm{H} \\ \tau &= \frac{L_{\mathrm{eq}}}{100\,\Omega} =10\,\mathrm{ms} \end{aligned}

Read the circuit

V1 applies a 0–5 V pulse through the 100 Ω resistor. The top and bottom wires join the two inductor branches. Current arriving through R1 divides at the upper junction and recombines on the lower return.

  • VL — green: the common voltage across both inductors.
  • IL1 — blue: current entering L1.
  • IL2 — purple: current entering L2.

The source current is the sum I=IL1+IL2I=I_{L1}+I_{L2}. Both current arrows point from the supply toward their inductors.

Why the smaller inductor takes more current

With equal applied voltage, the smaller inductance permits a faster current change. Because both currents start at zero, their ratio remains inverse to their inductances:

IL1IL2=L2L1=2IL1=23I,IL2=13II∞=5 V100 Ω=50 mA\begin{aligned} \frac{I_{L1}}{I_{L2}} &= \frac{L_2}{L_1}=2 \\ I_{L1} &= \frac{2}{3}I, \qquad I_{L2}=\frac{1}{3}I \\ I_{\infty} &= \frac{5\,\mathrm{V}}{100\,\Omega} =50\,\mathrm{mA} \end{aligned}

After a long high pulse, the two branch currents approach 33.3 mA and 16.7 mA. A lower inductance does not mean a lower DC resistance here: these ideal coils have no winding resistance. Their transient history establishes the current split.

Observe in CircuitSim

The pulse rises at 5 ms and falls at about 55 ms. The chart opens with voltage above the two current traces. At about 15 ms, IL1 is 21.1 mA and IL2 is 10.5 mA. When the source returns to zero, VL becomes negative and both positive currents decay continuously.

The saved transient uses Use initial conditions, with both inductor currents set to zero. This avoids an indeterminate DC current split in a loop of ideal inductors. The 0–110 ms run and 50 µs maximum step resolve the 10 ms response. Open Table for Time, VL, IL1, and IL2.

Try two changes

  1. Set L2 → Inductance to 1.5 H. The branch currents become equal, the equivalent inductance becomes 0.75 H, and the time constant becomes 7.5 ms. Each branch approaches 25 mA.
  2. Restore L2 to 3 H. Then double both values: L1 = 3 H, L2 = 6 H. The equivalent becomes 2 H and the time constant becomes 20 ms. The 2:1 split is unchanged, but the currents rise and decay more slowly. Restore 1.5 H and 3 H afterward.

Model assumptions

The coils have no mutual coupling or winding resistance. Nonzero initial currents can add circulating current and change the split. With real winding resistance, the eventual DC sharing depends on those resistances; it need not remain inverse to inductance.

Components used

Components used
3 components
NameManufacturerMPNCountType

Inductor

Generic

—

2

Official

Pulse Voltage Source

Generic

—

1

Official

Resistor

Generic

—

1

Official

Try this circuit yourself

Free to get started. No download — runs in your browser with a full SPICE engine.