Skip to main content

Thevenin's Theorem

CI

CircuitSim

·

Created Oct 3, 2026

·

Updated Oct 3, 2026

Preview will appear once the owner saves the schematic
Details

Components

2


Schematic

Yes


Simulation

DC operating point


Copies

Not copied yet

About this circuit

Compare a loaded resistor divider with its Thevenin equivalent. Both networks produce the same load voltage and current as the load changes.

Circuit notes

Thevenin's Theorem

A linear source network can be replaced, at two terminals, by one voltage source and one series resistance. The upper circuit is a loaded resistor divider. The lower circuit is its Thevenin equivalent. Both drive identical 1 kΩ loads.

Find the equivalent

First imagine removing RL1 from the upper circuit. The open-circuit output is the unloaded divider voltage. This is VthV_{\mathrm{th}}.

Next, remove the load and deactivate the independent 6 V source: replace an ideal voltage source with a short circuit. Looking into the output terminals, R1 and R2 are then in parallel. This gives RthR_{\mathrm{th}}.

Vth=6 V 1 kΩ1 kΩ+1 kΩ=3 VRth=R1∥R2=(1 kΩ)(1 kΩ)2 kΩ=500 Ω\begin{aligned} V_{\mathrm{th}} &= 6\,\mathrm{V}\, \frac{1\,\mathrm{k}\Omega}{1\,\mathrm{k}\Omega+1\,\mathrm{k}\Omega} =3\,\mathrm{V} \\ R_{\mathrm{th}} &= R_1\parallel R_2 \\ &=\frac{(1\,\mathrm{k}\Omega)(1\,\mathrm{k}\Omega)}{2\,\mathrm{k}\Omega} =500\,\Omega \end{aligned}

The lower circuit uses exactly these values: Vth = 3 V and Rth = 500 Ω. Each circuit has its own ground symbol to make the two comparison networks easy to trace; both symbols represent the same 0 V reference.

Compare the loaded results

  • Vorig — green: voltage across RL1 in the original network.
  • Veq — red: voltage across RL2 in the equivalent network.
  • Iorig — blue: current into the original load.
  • Ieq — purple: current into the equivalent load.

The load current and voltage follow directly from the equivalent:

IL=VthRth+RL=3 V500 Ω+1 kΩ=2 mAVL=ILRL=2 V\begin{aligned} I_L &= \frac{V_{\mathrm{th}}}{R_{\mathrm{th}}+R_L} =\frac{3\,\mathrm{V}}{500\,\Omega+1\,\mathrm{k}\Omega} =2\,\mathrm{mA} \\ V_L &= I_LR_L=2\,\mathrm{V} \end{aligned}

The loaded output is 2 V, not the 3 V open-circuit voltage. In the upper circuit RL1 loads the divider. In the lower circuit the same voltage drop appears across Rth.

Observe in CircuitSim

DC Operating Point runs automatically. The Table opens with Vorig, Veq, Iorig, and Ieq. Both voltage rows should read 2.0 V and both current rows 2.0 mA. A time chart is hidden because these are steady DC values.

Only behavior at the load terminals is equivalent. For example, the original source supplies 4 mA at the baseline, because R2 also draws current, while the equivalent source supplies 2 mA. The theorem does not preserve internal currents or total internal power.

Try two loads

Change both RL1 and RL2 so they remain equal, then run again:

  1. Set each Resistance to 500 Ω. Both outputs become 1.5 V, and both load currents become 3 mA.
  2. Set each Resistance to 2k. Both outputs become 2.4 V, and both load currents become 1.2 mA. Restore both loads to 1k afterward.

As the load resistance becomes very large, both output voltages approach 3 V and load current approaches zero. If you change V1, R1, or R2, recalculate and update Vth and Rth as well; the lower network is intentionally an explicit, editable equivalent.

Model assumptions

The sources and resistors are ideal and linear. The source-deactivation shortcut here applies to independent sources. Networks containing dependent sources generally require a test source when finding Thevenin resistance.

Components used

Components used
2 components
NameManufacturerMPNCountType

Resistor

Generic

—

5

Official

DC Voltage Source

Generic

—

2

Official

Try this circuit yourself

Free to get started. No download — runs in your browser with a full SPICE engine.