Skip to main content

Impedances of Same Magnitude

CI

CircuitSim

·

Created Oct 3, 2026

·

Updated Oct 3, 2026

Preview will appear once the owner saves the schematic
Details

Components

4


Schematic

Yes


Simulation

Transient analysis


Copies

Not copied yet

About this circuit

A resistor, inductor and capacitor each present 100 ohms of impedance magnitude at 100 Hz. Equal current amplitudes have different phases.

Circuit notes

Impedances of Same Magnitude

A resistor, inductor and capacitor each present 100 ohms of impedance magnitude at 100 Hz. Equal current amplitudes have different phases. Each source has a 1 V peak sinusoidal output. All branches share one ideal voltage source at 100 Hz.

Equal impedance magnitudes do not imply identical phase or identical energy use.

Calculate the response

R=100 ΩL=1002π(100)≈159.15 mHC=12π(100)(100)≈15.915 μF\begin{aligned} R&=100\,\Omega\\ L&=\frac{100}{2\pi(100)}\approx159.15\,\mathrm{mH}\\ C&=\frac{1}{2\pi(100)(100)}\approx15.915\,\mu\mathrm F \end{aligned}
BranchValueFrequencyPeak current
R1100 Ω100 Hz10 mA
L1159.15 mH100 Hz10 mA
C115.915 µF100 Hz10 mA
iR=10cos⁡(ωt) mAiL=10sin⁡(ωt) mAiC=−10sin⁡(ωt) mA\begin{aligned} i_R&=10\cos(\omega t)\,\mathrm{mA}\\ i_L&=10\sin(\omega t)\,\mathrm{mA}\\ i_C&=-10\sin(\omega t)\,\mathrm{mA} \end{aligned}

At 100 Hz the capacitor and inductor currents cancel at the source, while the resistor current stays in phase with voltage. All tabulated amplitudes are peak, not RMS; divide by 2\sqrt{2} for RMS.

Read the schematic and chart

The green V probe reads the shared voltage. IR is blue, IL purple and IC orange. A negative current means flow opposite the probe arrow.

The chart stacks voltage above current so volts and amperes have separate scales. The saved view shows 10–40 ms; the simulation runs from 0 to 40 ms with a 10 µs maximum step. Open Table for matching time samples and named columns. Compare equal peak heights and the quarter-cycle shifts.

Each source uses Phase = 90°, so its sine waveform begins at a cosine peak. Use initial conditions is enabled. Capacitors start at 1 V and inductors at 0 A; those values match the chosen steady sinusoid and avoid an artificial charging impulse or DC current offset. Initial samples are outside the saved chart view.

Try two changes

  1. Double V1 → Frequency from 100 to 200 Hz and run again. Capacitor current doubles to 20 mA, inductor current halves to 5 mA, and resistor current remains 10 mA. The three impedance magnitudes are no longer equal. Restore the original frequencies.
  2. Double R1 → Resistance, L1 → Inductance and C1 → Capacitance and run again. Resistor and inductor currents halve; capacitor current doubles. Restore the displayed values afterward.

Model assumptions

These are ideal linear components and ideal sources. Only the resistor dissipates average power; the capacitor and inductor exchange stored energy with the source. Real parts add leakage, winding resistance, ESR and parasitic reactance; inductors can saturate. The chosen initial energy is intentional and does not model connecting an unenergized part to a live source.

Components used

Components used
4 components
NameManufacturerMPNCountType

AC Voltage Source

Generic

—

1

Official

Capacitor

Generic

—

1

Official

Inductor

Generic

—

1

Official

Resistor

Generic

—

1

Official

Try this circuit yourself

Free to get started. No download — runs in your browser with a full SPICE engine.