Skip to main content

1_2_3_Invertierender_Verstärker (Copy)

BZ

Barta Zoltán

·

Created Nov 20, 2026

·

Updated Nov 20, 2026

Preview will appear once the owner saves the schematic
Details

Components

3


Schematic

Yes


Simulation

Interactive


Copies

Not copied yet

Tags

No tags yet.

About this circuit

Imported circuit. 2 import warning(s) were generated.

Circuit notes

Invertierender Verstärker


Versuch

  1. Interaktive Analyse: Messen Sie die Spannung Ua für Rk = 5k/10k/20k Ω.

Messtabelle

Re = 10 kΩ = konst.
Ue = 3V = konst.

Rk in kΩUa in VVURk/Re
5
10
20
  1. Leiten Sie die Formel zur Berechnung von Vu = Ua/Ue ab. Es sollen nur die Größen Rk und Re enthalten sein.
  2. Messen Sie die Übertragungskennlinie mit einem DC-Sweep.
    Die Eingangsspannung Ue (DC-Quelle) soll dabei von -20 V bis +20 V in 0,1 V-Schritten durchlaufen werden.
  3. Ändern Sie wieder Rk. Welchen Zusammenhang gibt es mit der Kennliniensteigung?

Für Profis

Die Formel kann auch über die Ströme und Spannungen an Rk und Re abgeleitet werden.
Hinweis: Ie = Ik und UE- = 0 (Spannung am invertierenden Eingang). Messe nach und leite die Formel ab.

Components used

Components used
3 components
NameManufacturerMPNCountType

DC Voltage Source

Generic

—

3

Official

Resistor

Generic

—

2

Official

Op Amp 5-Pin

Generic

—

1

Official

SPICE netlist

* **************************************************
* Generated from CircuitSim Schematic
**************************************************
* net label +Ub joins +Ub::component:node-2:T0 +Ub::node:stub-18
* net label -Ub joins -Ub::component:node-3:T0 -Ub::node:stub-20
X_OPV 0 N8 N1 N5 N6 Param5TVIRTUAL_5c55ebb8 IOS=20n AVOL=200k BW=100meg SR=10meg CMRR=100 ISC=25m RI=10meg VOS=1m IBS=80n RO=10
R_Re N7 N8 10k Resistor_1d9c8cf9a__R_Re temp=27
R_Rk N6 N8 5K Resistor_1d9c8cf9a__R_Rk temp=27
V_Uamax N5 0 dc -13.5 ac 0 0 distof1 0 0 distof2 0 0
V_Uamin N1 0 dc 13.5 ac 0 0 distof1 0 0 distof2 0 0
V_Ue1 N7 0 dc 3 ac 0 0 distof1 0 0 distof2 0 0
E_Ua Ua 0 N6 0 1
E_Ue Ue 0 N7 0 1

**************************************************
* Models and supporting definitions follow
**************************************************
.subckt Param5TVIRTUAL_5c55ebb8 In_p In_n Vpos Vneg Out params: VOS=1m IBS=80n IOS=20n AVOL=200K BW=100M SR=1M CMRR=100 ISC=25m RI=10M RO=10
    +SR=1Meg RO=75 ISC=25m RI=100meg VOS=0.1m IBS=1n IOS=1p
    .param Rp1=1e6
    .param Rs1=1e6
    .param K_Is2a=sqrt(AVOL)/Rs1
    .param K_Is2b=sqrt(AVOL)/Rp1
    .param Cp1={AVOL/(2*3.141592653589793*BW*Rp1)}
    .param CMRR_lin=10**(CMRR/20)

    Rin In_p In_n {RI}
    Bcm 4 3 V = {V(cm)/CMRR_lin}
    Voff In_p 4 {VOS}
    Ibias1 In_p 0 {IBS}
    Ibias2 In_n 0 {IBS}
    Ioffset In_p In_n {IOS/2}

    Rcm1 In_p cm 10meg
    Rcm2 In_n cm 10meg

    BIs1a vref vs2a I = {K_Is2a*(V(3)-V(In_n))}
    Rs1 vs2a vref {Rs1}

    BIs2b vref vs2b I = {K_Is2b*(V(vs2a)-v(vref))}
    Rp1 vs2b vref {Rp1}
    VCp1sense vs2b vs2b_ 0
    Cp1 vs2b_ vref {Cp1}

    D3 vs2b_ 8 Param5TVIRTUAL_5c55ebb8_LimitDiode
    D4 8 vpos Param5TVIRTUAL_5c55ebb8_LimitDiode
    B_SRp 8 vpos I={I(VCp1sense)- (Cp1*SR)}

    D5 10 vs2b_ Param5TVIRTUAL_5c55ebb8_LimitDiode
    D6 Vneg 10 Param5TVIRTUAL_5c55ebb8_LimitDiode
    B_SRn Vneg 10 I={-1*I(VCp1sense)-(Cp1*SR)}

    DVpclip vs2b_ Vpos Param5TVIRTUAL_5c55ebb8_VLimit
    DVnclip Vneg vs2b_ Param5TVIRTUAL_5c55ebb8_VLimit

    Bout vref out_ I={(V(vs2b)-v(vref))/RO}
    Rout vref out_ {RO}
    Voutsense out_ out 0

    D9 out 15 Param5TVIRTUAL_5c55ebb8_LimitDiode
    D10 15 vpos Param5TVIRTUAL_5c55ebb8_LimitDiode
    B_outp 15 vpos I={I(Voutsense)- ISC}

    D11 16 out Param5TVIRTUAL_5c55ebb8_LimitDiode
    D12 vneg 16 Param5TVIRTUAL_5c55ebb8_LimitDiode
    B_outn vneg 16 I={-1*I(Voutsense)-ISC}

    R5 Vpos mid 1000000
    R6 mid Vneg 1000000
    Eref vref 0 mid 0 1

.ends

.MODEL Param5TVIRTUAL_5c55ebb8_LimitDiode D (IS= 1.0e-12)
.MODEL Param5TVIRTUAL_5c55ebb8_VLimit D(n=0.1)
.model Resistor_1d9c8cf9a__R_Re r(tc1=0 tc2=0 tnom=27)
.model Resistor_1d9c8cf9a__R_Rk r(tc1=0 tc2=0 tnom=27)

**************************************************
* Simulation settings
**************************************************
.options rshunt=1e12
.tran 200p 1e12 0 200p
.save V(Ue) V(Ua)
.end

Try this circuit yourself

Free to get started. No download — runs in your browser with a full SPICE engine.