Diode Limiter (Copy)
ggggg-ggggg
·
Created Oct 4, 2026
·
Updated Oct 4, 2026
Details
Components
3
Schematic
Yes
Simulation
Transient analysis
Copies
Not copied yet
Tags
No tags yet.
About this circuit
Limit both polarities of a signal with antiparallel diodes and a series resistor.
Circuit notes
Diode Limiter
Limit both polarities of a signal with antiparallel diodes and a series resistor.
V1 applies a ±5 V, 1 kHz sine wave through R1 = 1 kΩ. D1 and D2 are antiparallel from the output to the return. Each diode conducts on a different polarity. RL = 100 kΩ is a light load.
The output flattens around ±0.7 V at large input amplitudes. At small amplitudes the diodes are nearly off and the output follows the input. A diode threshold is gradual and depends on current; it is not an exact hard switch.
Read the results. Vin is green, Vout red and the input-resistor current Iin blue. The current plot shows where the source supplies clipping current.
Model limits. Ideal bias and signal sources have unlimited current capability. R1 is essential for limiting current. Junction capacitance, reverse recovery, heating and source impedance are omitted.
Try it. Set V1 peak voltage to 0.2 V; the small signal passes with little limiting. Restore the original values after comparing the results.
Components used
Components used
3 components
SPICE netlist
* **************************************************
* Generated from CircuitSim Schematic
**************************************************
X_D1 N2 0 DIODE_25d079d4 IS=10f RS=0 N=1 BV=1e30 IBV=100p CJO=0 VJ=1 M=0.5 TT=0 EG=1.11 XTI=3 KF=0 AF=1 FC=0.5 ISR=0 NR=2 IKF=1e30 TNOM=27 IC=0 TEMP=27
X_D2 0 N2 DIODE_25d079d4 IS=10f RS=0 N=1 BV=1e30 IBV=100p CJO=0 VJ=1 M=0.5 TT=0 EG=1.11 XTI=3 KF=0 AF=1 FC=0.5 ISR=0 NR=2 IKF=1e30 TNOM=27 IC=0 TEMP=27
R_R1 N1 N2 1k Resistor_1d9c8cf9a__R_R1
V_V1 N1 0 dc 0 ac 1 0 distof1 0 0 distof2 0 0 sin ( 0 5 100 0 0 0 )
E_VP_1 VP_1 0 N1 0 1
E_VP_2 VP_2 0 N2 0 1
**************************************************
* Models and supporting definitions follow
**************************************************
* Source-compatible two-terminal junction diode
.subckt DIODE_25d079d4 A K params: IS=1e-14 RS=0 N=1 BV=1e30 IBV=100p CJO=0 VJ=1 M=0.5 TT=0 EG=1.11 XTI=3 KF=0 AF=1 FC=0.5 ISR=0 NR=2 IKF=1e30 TNOM=27 IC=0 TEMP=27
.model DIODE_25d079d4_CORE D(IS={IS} RS={RS} N={N} BV={BV} IBV={IBV} CJO={CJO} VJ={VJ} M={M} TT={TT} EG={EG} XTI={XTI} KF={KF} AF={AF} FC={FC} ISR={ISR} NR={NR} IKF={IKF} TNOM={TNOM})
DCORE A K DIODE_25d079d4_CORE IC={IC} TEMP={TEMP}
.ends DIODE_25d079d4
.model Resistor_1d9c8cf9a__R_R1 r(tc1=0 tc2=0 tnom=27)
**************************************************
* Simulation settings
**************************************************
.tran 1u 3m 0 1u
.save V(VP_1) V(VP_2)
.endTry this circuit yourself
Free to get started. No download — runs in your browser with a full SPICE engine.